How the map area calculator works
Every point you tap is stored as a latitude and a longitude. Join the points in order and you get a closed shape, called a polygon. The tool works out the area inside that polygon each time you add, move or remove a point.
On a small sheet of paper you could use flat geometry. The Earth is not flat, though, and a degree of longitude gets shorter as you move away from the equator. In Lahore it is about 95 km wide; near the North Pole it shrinks to almost nothing. So the tool treats the Earth as a sphere with a radius of 6,378,137 m and adds up thin strips between each side of your shape and the equator. Strips going one way count as plus, strips going back count as minus, and what is left is the area inside.
This is the same formula used by popular mapping libraries such as Turf.js. For a plot or a field the answer is within 1% of the true area on the real, slightly squashed Earth (0.3 to 0.4% in Pakistan), which is far smaller than the error from tapping.
The perimeter is the sum of the side lengths. Each side is measured on the WGS84 ellipsoid, the same model of the Earth that GPS uses, so it is accurate to well under a centimetre for the points you chose.
How to measure a plot step by step
- Find the place. Type the town, area or block in the search box, for example “Johar Town, Lahore”, and pick a result. Then pan and zoom by hand to your street.
- Zoom right in. Use the + button or pinch until the plot fills a good part of the map. At the closest zoom, one screen pixel covers about a quarter of a metre.
- Tap the corners in order. Start at one corner and go round the edge, clockwise or anticlockwise. Point 1 is amber so you can see where you began. You do not need to tap the first point again: the shape closes itself.
- Fine-tune. Drag any numbered point onto the exact corner. Made a wrong tap? Press Undo last point, or remove any point from the list under the map.
- Read the result. The area appears in every unit at once. Pick your marla size if you need marla and kanal, then press Copy result.
If two sides cross, like a figure of eight, the tool warns you. That happens when you tap corners out of order, and the area of such a shape is meaningless.
Worked example: a 1 kanal plot in Lahore
A common 1 kanal plot in a Lahore society is 50 ft wide and 90 ft deep. Trace its four corners and the tool shows about:
- 50 × 90 = 4,500 sq ft, which is 4,500 × 0.09290304 = 418.06 m²
- 4,500 ÷ 225 = 20 marla with the Lahore marla of 225 sq ft, so exactly 1 kanal
- 4,500 ÷ 43,560 = 0.103 acres
- A perimeter of 2 × (50 + 90) = 280 ft, or 85.34 m
Now switch the marla size to 272.25 sq ft, the revenue marla. The same land becomes 4,500 ÷ 272.25 = 16.53 marla. Nothing about the ground changed; only the unit did. That is why the marla size matters so much when you compare plots. The land area converter explains the different marla standards in more detail.
Worked example: a farm field
Say you trace a rectangular field that measures 200 m by 100 m on the map:
- Area = 200 × 100 = 20,000 m² = 2 hectares
- 20,000 ÷ 4,046.8564224 = 4.94 acres
- With the 272.25 sq ft revenue marla, that is 215,278 sq ft ÷ 5,445 = 39.5 kanal
- Perimeter = 600 m, or about 0.37 miles
Tips for an accurate result
- Zoom in before you tap. At low zoom, one tap can be several metres off. The closer you zoom, the smaller the error.
- Trace the real corners. Walls, fences and road edges are often drawn on the map. Use them, and add extra points where a boundary bends.
- Mind the map offset. Buildings and plot lines on any map can sit a metre or two away from their real position. Errors like this matter most on small plots.
- Small errors add up. If your trace of a 50 × 90 ft plot comes out 51 × 91 ft, the area grows to 4,641 sq ft, about 3% or 0.6 marla more.
- Roofs are sloped. A map shows a roof from above, so you get its flat footprint. For the real surface of a pitched roof, use the roofing calculator.
Treat the result as a good estimate, not a legal measurement. For a sale, an inheritance split, a dispute or the land record, rely on a licensed surveyor or the official record.
Area units at a glance
| Unit | In square metres | In square feet |
|---|---|---|
| 1 square foot | 0.0929 | 1 |
| 1 square yard (gaz) | 0.8361 | 9 |
| 1 marla (Lahore, 225 sq ft) | 20.90 | 225 |
| 1 marla (revenue, 272.25 sq ft) | 25.29 | 272.25 |
| 1 kanal (Lahore, 20 marla) | 418.06 | 4,500 |
| 1 acre | 4,046.86 | 43,560 |
| 1 hectare | 10,000 | 107,639 |
| 1 square kilometre | 1,000,000 | 10,763,910 |
Already know the measurements?
You do not need a map if you have the side lengths. For rectangles, triangles, circles and other regular shapes, the area calculator shows the formula and the steps. For rooms and flooring, add up each space with the square footage calculator.